SKYDEK II

Home | Products | About us | Corporate | Contact us

Duro Products
	Skydek II
	3 Pan Klip System
	Durospan
	V-Clad 750
	Durodek™
	C & Z Purlins

DURO Metal Industrial (M) Sdn Bhd, is one of the Malaysia's largest and most global metal roofing and structural manufacturer & distributor. Today, DURO Metal can pride itself for meeting stringent standards in a global market for its manufacturing and technological innovations.

SKYDEK II - Ultra Modern! Ultra Light! Ultra Strong!

An Ideal choice for saving cost and time in modern construction. Its contemporary design coupled with the inherent properties of high tensile steel makes it suitable for vertical cladding and roofing to as low as 3º pitch. It is popularly used for residential, industrial and commercial applications.

	Economy				Regular
	Galvalume	Colorlume	Galvalume	Colorlume	Galvalume	Colorlume
Base Metal Thickness	0.30		0.35		0.42
Total Coated Thickness	0.35		0.40		0.47
Mass per unit area (kg/m²)	3.14	3.19	3.65	3.68	4.29	4.36
Mass per unit length (kg/m)	2.38	2.43	2.74	2.80	3.26	3.32
Coverage (m²/t)	318	313	277	271	233	229

Table 1- Maximum Allowable Support Spacing

Base Metal Thickness	Total Coated Thickness	Roofs					Walls
Base Metal Thickness	Total Coated Thickness	Single Span	End Span	Internal Span Overhang	Unstiffened Overhang	Stiffened	Single Span	End Span	Internal Span	Overhangs
0.30mm	0.35mm	700	700	1300	110	220	1300	1300	1560	110
0.35mm	0.40mm	850	850	1500	130	260	1550	1550	1880	130
0.42mm	0.47mm	1000	1000	1700	150	300	1800	1800	2200	150

Load Distributed Capacity Over Continuous Span Condition.

Base Metal Thickness	Span (mm)		900	1200	1500	1800	2100	2400
0.30mm	Safe Load Distribution	kPa	1.3	0.7	0.2	0.2	0.3	0.1
	Deflection Under Above Load	mm	2.7	3.2	4.4	6.2	6.0	6.0
	Safe Wind Uplift	kPa	3.1	2.4	1.8	2.0	1.7	1.5
0.35mm	Safe Load Distribution	kPa	3.0	2.1	1.2	0.8	0.5	0.3
	Deflection Under Above Load	mm	2.8	4.0	6.0	8.0	10	12
	Safe Wind Uplift	kPa	3.4	2.6	2.0	1.8	1.4	1.2
0.42mm	Safe Load Distribution	kPa	6.2	3.5	2.3	1.5	1.1	0.9
	Deflection	mm	2.9	4.8	7.6	9.8	14	18
	Safe Wind Load	kPa	3.7	2.8	2.2	1.6	1.1	0.9

Standard Thickness

THK	Material Coating
MM/bst	Material Coating
0.30	Colorcoat	N.A	N.A	N.A
0.35	Colorcoat	Zincalume	Colorbond	Prima Maju
0.42	Colorcoat	Zincalume	Colorbond	Prima Maju
0.48	Colorcoat	Zincalume	Colorbond	Prima Maju
0.60	N.A	Zincalume	Colorbond	N.A

Tolerances

Length: +0, -15mm

Cover width: ± 4mm

Packing

Sheets are packed in strapped bundles of one tonne maximum mass

Lengths

All products are available from Duro Distributors in length up to 21 meters customs - cut to your length requirements. Lengths longer than 21 meters can be supplied, provided satisfactory transport and on-site handling can be arranged.

Minimum Roof Slope

The normal recommended minimum roof slope is 1 in 20 (approximately 3º). However, in non-cyclonic areas where roofs are in single sheet lengths, with a run of less than 15 meters, a minimum roof slope of 1 in 30 (approximately 2º) may be used. For recommended slope of roofs in cyclonic areas, please consult our Duro Distributor's Office.

Sheet Laying and Fastening

SKYDECK II